Home > Technology > Content

User Guidance of Wired Anycast for Portable Mini LED Projector

User Guidance of Wired Wifi Display Dongle Anycast for Portable Mini LED Projector


image002.jpgimage003.jpg 


Hardware Installation


image006.jpg

Please follow below steps to setup Anycast:

(1) Connect Anycast to your Projector via HDMI port;

(2) Connect the USB plug of Anycast with an external (5V1A) adapter;

(3a) iOS: Connect the lightning plug of Anycast with your iOS device;

Note: Support iOS8 and above!

(3b) Android: Connect the micro USB cable of Anycast with your Android device;

(4) Switch Projector to HDMI source, if the HD source is set correctly, you should see the Anycast setup screen on Projector;

(5) iOS: If your iOS device popups a message “Trust This Computer”, please select “Trust” and wait for a few seconds for initialization, the screen of your iOS device will be shown on Projector.

Note: Some iOS devices may popup "This accessory may not be supported".  Please feel at ease to use as this is a normal notification.


For iOS (iPhone/iPad) Device: 

1. Firmware Upgrade


image008.jpg


(1) Insert a paper clip into the hole on the Anycast, and push the key inside the hole to enable HotSpot mode (Internet);

Note: Some Anycasts don’t need to do this, if no need, start from step 2!

(2) Enable “Personal HotSpot” of your iOS device;

Note: Cellular (3G/4G) data is needed at your iOS device!

(3) Download and install “EZCast” App, launch it. Click the “Wire” Button on the right to establish connection, and then click the “Menu” Button on the left;

(4) Click the “Firmware OTA” button.

Note: Please DO NOT power off during upgrade! 


2. Output Resolution


image010.jpg


(1) Insert a paper clip into the hole on the Anycast, and push the key inside the hole to enable HotSpot mode (Internet);

Note: Some Anycasts don’t need to do this, if no need, start from step 2!

(2) Enable “Personal HotSpot” of your iOS device;

Note: Cellular (3G/4G) data is needed at your iOS device!

(3) Launch EZCast App. Click the “Wire” Button on the right to establish connection, and then click the “Menu” Button;

(4) Click the “Setting” button;

(5) Use the keypad to control Anycast;

(6) Switch to your favor output resolution (ex. 1080p).


For Android Device: 

1. Software Installation

Please download “EZCast” from Google play (Android).

You may also scan the QR code on Projector to download.

Note: Supports Android 4.4 and above! Not all Android 4.4 devices support USB Mirror! Not all smartphone supports USB audio and consequently the sound may come from the smartphone instead of Projector! 

2. Setup Anycast

(A) Android USB tethering mode

Please launch the “EZCast” app, and click the “Wire” button. After that please click the “Connect” button, and then enable “USB tethering”. Then you may start mirroring your Android screen.

Note: Supports Android 5.0 and above!


image012.jpg


(B) Android USB Mirror mode

USB Mirror mode is an alternative for supporting more Android devices (4.4 and above). Please launch the “EZCast” app, and then enable “USB tethering” according to previous section.


image013.jpgimage016.jpg


Click the “Menu” button, and then “USB Mirror” button on menu page, and follow the App instructions to enable “USB debugging”. You may start mirroring your Android screen. If “USB Mirror” failed to enable, please unplug USB cable from your Android device, and then re-plug in for retry.

Note: Supports Android 4.4 and above! USB debugging should be turned on for activating USB Mirror! Not all Android 4.4 devices support USB Mirror! 

3. Android Audio Control

Some Android devices might fail to convey audio/sound through “USB Mirror”. Please use below alternatives to switch on Android’s speaker.

Press audio switch button on the case: If your Anycast contains a button on the case, you may press the button for switching audio/sound to your Android’s speaker. You may also see the sound status change on the right-top concern of your Projector screen as shown below.


image018.jpg

 

(top) Output from “Phone”          (bottom) Output from “Dongle”

 

4. Firmware Upgrade and Setting

Please launch the “EZCast” app, and click the “Wire” button to establish “Android USB tethering mode” connection between your Android device and Anycast. After that please click the “Menu” button and then the “Setting” button, and then you can config Anycast from the control pad as shown below.


image020.jpg


(1) Language: Change the language of the Anycast

(2) Resolution: Change the output resolution of the Anycast

(3) Upgrade: IMPORTANT! Please upgrade your Anycast to the latest version according to the App instruction in order to compatible with up-to-date devices (iOS and Android).

Note: It may consume your 3G/4G data traffic during upgrade of Anycast! 


EZCast App 

EZChannel (Main Menu): to discover/search video and to enable Autoplay function

Video and Music (Main Menu): to watch and listen to local media files at your device

Mirror On/Off (Android) (Menu > Mirror On/Off): to mirror your Android's screen to your Projector

USB Mirror (Android)(Menu > USB Mirror): to turn on USB Mirror for your Android device

Firmware OTA (iOS) (Menu > Firmware OTA): to upgrade firmware for your Anycast

Setting (Menu > Setting): to turn on Air Setup for system configuration


http://www.3d-vr-projector.com/

Contact Us

Tel: +86-755-36940793

Fax: +86-755-23708113
E-mail: easam@easuntech.com

Address: 5th Floor, East Block A9, Longwangmiao Industrial Building, East Baishisha, Fuyong Street, Bao'an, Shenzhen, China

Copyright © Shenzhen EASUN Electronic Technology Co.,Ltd
Tel: +86-755-36940793
Fax:+86-755-23708113
E-mail:easam@easuntech.com
Address:5th Floor, East Block A9, Longwangmiao Industrial Building, East Baishisha, Fuyong Street, Bao'an, Shenzhen, China